[Jul 02, 2026] NACE-CIP2-001 Exam Dumps, NACE-CIP2-001 Practice Test Questions
Free NACE-CIP2-001 Study Guides Exam Questions and Answer
NACE-CIP2-001 (Coating Inspector Level 2) Exam is a certification exam offered by the National Association of Corrosion Engineers (NACE) International. NACE-CIP2-001 exam is designed for professionals in the coating industry who wish to demonstrate their knowledge and experience in the inspection of coatings. As a Level 2 certification, it requires a greater level of knowledge and experience than the Level 1 certification.
NEW QUESTION # 14
Which product, when closely inspected has a green or red layer of fusion bonded epoxy (FBE) that is visible directly on the steel?
- A. Fusion Bonded Epoxy
- B. 2-Layer Polyethylene (PE)
- C. 3-Layer Polyethylene (PE)
- D. Coal Tar Enamel
Answer: C
NEW QUESTION # 15
You can use magnifiers to examine all of the following EXCEPT
- A. Surface profile
- B. Surface cleanliness
- C. Mill scale
- D. Blisters
Answer: B
NEW QUESTION # 16
You are a NACE Level 2 Coating Inspector who has just arrived on a job in progress where there is no Inspection and Test Plan (ITP). The first morning you arrive the job is behind schedule and you are asked to take DIY Film Thickness readings.
Your FIRST preferred course of action is to:
- A. Develop your own methodology and proceed take the readings
- B. Call your supervisor
- C. Refuse to take readings until an is in place
- D. Use a generally accepted industry standard and to take readings
Answer: D
NEW QUESTION # 17
You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:
- A. Review the NCR with the other Inspector
- B. Consult your supervisor
- C. Verbally challenge the NCR
- D. Request a re-blast of the item in question
Answer: B
NEW QUESTION # 18
When NACE/SSPC WJ 1 is referenced; what type of equipment would the Inspector expect to see on the job:
- A. Water Jetting Equipment
- B. Abrasive Blasting Equipment
- C. Scarifiers
- D. Power Tools
Answer: A
NEW QUESTION # 19
Ideally, documentation requirements should be defined:
- A. By the contractor
- B. At the pre-job conference
- C. In the specification
- D. By the inspector
Answer: C
NEW QUESTION # 20
Which is used to calibrate a pH meter?
- A. Deionized water
- B. Standard solvent solution
- C. Standard buffer solution
- D. Distilled water
Answer: C
NEW QUESTION # 21
The Inspectors' goal at the Pre-Job Conference is to:
- A. Discuss contractual requirements
- B. Take accurate meeting minutes for distribution
- C. Obtain a clear understanding of the Specification
- D. Manage the meeting so it doesn't go off topic
Answer: C
NEW QUESTION # 22
When performing testing in accordance with ASTM D 2583 the inspector may observe:
- A. Cold flow or creep
- B. Adhesion failure
- C. Glue failure
- D. Cohesion failure
Answer: A
NEW QUESTION # 23
The Concrete Repair Institute's comparators can be used to assess:
- A. Contamination levels prior to coating
- B. Surface cleanliness prior to coating
- C. Compressive and tensile strength prior to coating
- D. Surface profile prior to coating
Answer: D
NEW QUESTION # 24
When completing the Final Inspection report the Inspector should write the report using:
- A. Language that only in the project would understand
- B. Language that only technical experts would understand
- C. Language that another NACE Inspector would understand
- D. Language that the most would understand
Answer: D
NEW QUESTION # 25
You are the NACE Level 2 inspector reviewing the documentation from a NACE Level 1 you notice significant documentation errors.
Your FIRST preferred course of action is to:
- A. Correct the errors yourself and suggest the Level 1 inspector be replaced
- B. Have the Level 1 Inspector correct the errors and set up remedial training to improve the quality of documentation
- C. Correct the errors yourself and advise your supervisor that the Level 1 Inspector is incompetent
- D. Correct the errors yourself and submit the reports without any further action
Answer: B
NEW QUESTION # 26
Inspection and Test plans are developed by referencing:
- A. The Specification, TDS, relevant Standards and Codes
- B. The Specification, Application Guidelines, 'Relevant Standards and Codes
- C. The Specification, Safety Manual, Relevant Standards and Codes
- D. The Specification, SDS, relevant Standards and Codes
Answer: A
NEW QUESTION # 27
Which product, is used in conjunction with other coatings such as FBE when the lines run through wetlands or a body of water?
- A. 3-Layet Polyethylene (PE)
- B. Concrete
- C. Coal Tar Enamel
- D. 2-Layet Polyethylene (PE)
Answer: B
NEW QUESTION # 28
When observing design defects the NACE Inspector should:
- A. Stop the job immediately
- B. Ignore the defect as the inspector can't change the design
- C. Request that the item be rebuilt with a better design for coating
- D. Document the defect and the potential problems that could result
Answer: D
NEW QUESTION # 29
Inspectors perform tests on linings that they may not perform on exterior coatings because
- A. linings are more durable than coatings.
- B. coatings are expected to degrade over time.
- C. linings protect the contents and the container.
- D. coatings are more durable than linings.
Answer: C
NEW QUESTION # 30
Which surface preparation method uses a dilute acid solution to remove laitance and I roughen the concrete surface?
- A. High-pressure water washing
- B. Acid etching
- C. Stoning
- D. Sacking
Answer: B
NEW QUESTION # 31
You are the NACE Coating Inspector on a tank lining project and are asked to perform a high voltage holiday test after the coating applicators have completed their final repairs. After meeting all the confined space entry permit you enter the tank and notice a very strong odor of solvent.
Your first course of action should to:
- A. Investigate to find the source of the odor
- B. Exit the tank and immediately and report the problem to the nearest safety supervisor
- C. Don your air supplied respirator and continue the testing
- D. Exit the tank and document the incident in your daily report
Answer: B
NEW QUESTION # 32
In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?
- A. Cure stage
- B. Flow stage
- C. Wetting stage
- D. Gel stage
Answer: B
NEW QUESTION # 33
......
The Coating Inspector Level 2 certification exam consists of two parts: a written exam and a practical exam. The written exam consists of 120 multiple-choice questions that cover all aspects of the coatings industry. The practical exam requires candidates to demonstrate their knowledge and skills in performing coatings inspection tasks in a simulated environment. Candidates must pass both parts of the exam to become certified.
NACE-CIP2-001 Exam Dumps, NACE-CIP2-001 Practice Test Questions: https://certificationsdesk.examslabs.com/NACE/CIP-Level-2/best-NACE-CIP2-001-exam-dumps.html