[Jan-2024] HPE6-A84 Dumps are Available for Instant Access using ExamsLabs
HPE6-A84 Dumps 2024 - New HP HPE6-A84 Exam Questions
NEW QUESTION # 11
Refer to the scenario.
A customer requires these rights for clients in the "medical-mobile" AOS firewall role on Aruba Mobility Controllers (MCs):
Permitted to receive IP addresses with DHCP
Permitted access to DNS services from 10.8.9.7 and no other server
Permitted access to all subnets in the 10.1.0.0/16 range except denied access to 10.1.12.0/22 Denied access to other 10.0.0.0/8 subnets Permitted access to the Internet Denied access to the WLAN for a period of time if they send any SSH traffic Denied access to the WLAN for a period of time if they send any Telnet traffic Denied access to all high-risk websites External devices should not be permitted to initiate sessions with "medical-mobile" clients, only send return traffic.
The exhibits below show the configuration for the role.
There are multiple issues with the configuration.
What is one of the changes that you must make to the policies to meet the scenario requirements? (In the options, rules in a policy are referenced from top to bottom. For example, "medical-mobile" rule 1 is "ipv4 any any svc-dhcp permit," and rule 8 is "ipv4 any any any permit'.)
- A. In the "medical-mobile" policy, change the subnet mask in rule 3 to 255.255.248.0.
- B. In the "medical-mobile" policy, change the source in rule 1 to "user."
- C. Move the rule in the "apprf-medical-mobile-sacl" policy between rules 7 and 8 in the "medical-mobile" policy.
- D. In the "medical-mobile" policy, move rules 6 and 7 to the top of the list.
Answer: A
NEW QUESTION # 12
A customer has an AOS 10-based solution, including Aruba APs. The customer wants to use Cloud Auth to authenticate non-802.1X capable IoT devices.
What is a prerequisite for setting up the device role mappings?
- A. Integrating Aruba ClearPass Policy Manager (CPPM) and Device Insight
- B. Creating global role-to-role firewall policies in Central
- C. Configuring Device Insight (client profile) tags in Central
- D. Configuring a NetConductor-based fabric
Answer: C
Explanation:
Explanation
According to the Aruba Cloud Authentication and Policy Overview1, one of the prerequisites for configuring Cloud Authentication and Policy is to configure Device Insight (client profile) tags in Central. Device Insight tags are used to identify and classify IoT devices based on their behavior and characteristics. These tags can then be mapped to client roles, which are defined in the WLAN configuration for IAPs2. Client roles are used to enforce role-based access policies for the IoT devices. Therefore, option B is the correct answer.
Option A is incorrect because NetConductor is not related to Cloud Authentication and Policy. NetConductor is a cloud-based network management solution that simplifies the deployment and operation of Aruba Instant networks.
Option C is incorrect because integrating Aruba ClearPass Policy Manager (CPPM) and Device Insight is not a prerequisite for setting up the device role mappings. CPPM and Device Insight can work together to provide enhanced visibility and control over IoT devices, but they are not required for Cloud Authentication and Policy.
Option D is incorrect because creating global role-to-role firewall policies in Central is not a prerequisite for setting up the device role mappings. Global role-to-role firewall policies are used to define the traffic rules between different client roles across the entire network, but they are not required for Cloud Authentication and Policy.
NEW QUESTION # 13
A customer needs you to configure Aruba ClearPass Policy Manager (CPPM) to authenticate domain users on domain computers. Domain users, domain computers, and domain controllers receive certificates from a Windows CA. CPPM should validate these certificates and verify that the users and computers have accounts in Windows AD. The customer requires encryption for all communications between CPPM and the domain controllers.
You have imported the root certificate for the Windows CA to the ClearPass CA Trust list.
Which usages should you add to it based on these requirements?
- A. LDAP and Aruba infrastructure
- B. EAP and Radsec
- C. EAP and AD/LDAP Server
- D. Radec and Aruba infrastructure
Answer: B
NEW QUESTION # 14
You need to install a certificate on a standalone Aruba Mobility Controller (MC). The MC will need to use the certificate for the Web UI and for implementing RadSec with Aruba ClearPass Policy Manager. You have been given a certificate with these settings:
Subject: CN=mc41.site94.example.com
No SANs
Issuer: CN=ca41.example.com
EKUs: Server Authentication, Client Authentication
What issue does this certificate have for the purposes for which the certificate is intended?
- A. It lacks a DNS SAN.
- B. It has conflicting EKUs.
- C. It is issued by a private CA.
- D. It specifies domain info in the CN field instead of the DC field.
Answer: A
NEW QUESTION # 15
Refer to the scenario.
# Introduction to the customer
You are helping a company add Aruba ClearPass to their network, which uses Aruba network infrastructure devices.
The company currently has a Windows domain and Windows CA. The Window CA issues certificates to domain computers, domain users, and servers such as domain controllers. An example of a certificate issued by the Windows CA is shown here.
The company is in the process of adding Microsoft Endpoint Manager (Intune) to manage its mobile clients.
The customer is maintaining the on-prem AD for now and uses Azure AD Connect to sync with Azure AD.
# Requirements for issuing certificates to mobile clients
The company wants to use ClearPass Onboard to deploy certificates automatically to mobile clients enrolled in Intune. During this process, Onboard should communicate with Azure AD to validate the clients. High availability should also be provided for this scenario; in other words, clients should be able to get certificates from Subscriber 2 if Subscriber 1 is down.
The Intune admins intend to create certificate profiles that include a UPN SAN with the UPN of the user who enrolled the device.
# Requirements for authenticating clients
The customer requires all types of clients to connect and authenticate on the same corporate SSID.
The company wants CPPM to use these authentication methods:
* EAP-TLS to authenticate users on mobile clients registered in Intune
* TEAR, with EAP-TLS as the inner method to authenticate Windows domain computers and the users on them To succeed, EAP-TLS (standalone or as a TEAP method) clients must meet these requirements:
Their certificate is valid and is not revoked, as validated by OCSP
The client's username matches an account in AD
# Requirements for assigning clients to roles
After authentication, the customer wants the CPPM to assign clients to ClearPass roles based on the following rules:
* Clients with certificates issued by Onboard are assigned the "mobile-onboarded" role
* Clients that have passed TEAP Method 1 are assigned the "domain-computer" role Clients in the AD group "Medical" are assigned the "medical-staff" role Clients in the AD group "Reception" are assigned to the "reception-staff" role The customer requires CPPM to assign authenticated clients to AOS firewall roles as follows:
* Assign medical staff on mobile-onboarded clients to the "medical-mobile" firewall role
* Assign other mobile-onboarded clients to the "mobile-other" firewall role
* Assign medical staff on domain computers to the "medical-domain" firewall role
* All reception staff on domain computers to the "reception-domain" firewall role
* All domain computers with no valid user logged in to the "computer-only" firewall role
* Deny other clients access
# Other requirements
Communications between ClearPass servers and on-prem AD domain controllers must be encrypted.
# Network topology
For the network infrastructure, this customer has Aruba APs and Aruba gateways, which are managed by Central. APs use tunneled WLANs, which tunnel traffic to the gateway cluster. The customer also has AOS-CX switches that are not managed by Central at this point.
# ClearPass cluster IP addressing and hostnames
A customer's ClearPass cluster has these IP addresses:
* Publisher = 10.47.47.5
* Subscriber 1 = 10.47.47.6
* Subscriber 2 = 10.47.47.7
* Virtual IP with Subscriber 1 and Subscriber 2 = 10.47.47.8
The customer's DNS server has these entries
* cp.acnsxtest.com = 10.47.47.5
* cps1.acnsxtest.com = 10.47.47.6
* cps2.acnsxtest.com = 10.47.47.7
* radius.acnsxtest.com = 10.47.47.8
* onboard.acnsxtest.com = 10.47.47.8
You have started to create a CA to meet the customer's requirements for issuing certificates to mobile clients, as shown in the exhibit below.
What change will help to meet those requirements and the requirements for authenticating clients?
- A. Specify an OCSP responder, setting the hostname to localhost.
- B. Change the EST Digest Algorithm to SHA-512.
- C. Change the EST authentication method to use an external validator.
- D. Recreate the CA as a registration authority under Azure AD.
Answer: C
NEW QUESTION # 16
Refer to the scenario.
A customer is migrating from on-prem AD to Azure AD as its sole domain solution. The customer also manages both wired and wireless devices with Microsoft Endpoint Manager (Intune).
The customer wants to improve security for the network edge. You are helping the customer design a ClearPass deployment for this purpose. Aruba network devices will authenticate wireless and wired clients to an Aruba ClearPass Policy Manager (CPPM) cluster (which uses version 6.10).
The customer has several requirements for authentication. The clients should only pass EAP-TLS authentication if a query to Azure AD shows that they have accounts in Azure AD. To further refine the clients' privileges, ClearPass also should use information collected by Intune to make access control decisions.
You are planning to use Azure AD as the authentication source in 802.1X services.
What should you make sure that the customer understands is required?
- A. Azure AD Domain Services
- B. An app registration on Azure AD that references the CPPM's FQDN
- C. Windows 365 subscriptions
- D. CPPM's RADIUS certificate was imported as trusted in the Azure AD directory
Answer: B
Explanation:
Explanation
To use Azure AD as the authentication source in 802.1X services, you need to configure CPPM as a SAML service provider and Azure AD as a SAML identity provider. This allows CPPM to use Azure AD for user authentication and role mapping. To do this, you need to create an app registration on Azure AD that references the CPPM's FQDN as the reply URL and the entity ID. You also need to grant the app registration the required permissions to access user information from Azure AD1
NEW QUESTION # 17
Refer to the scenario.
A customer has an AOS10 architecture that is managed by Aruba Central. Aruba infrastructure devices authenticate clients to an Aruba ClearPass cluster.
In Aruba Central, you are examining network traffic flows on a wireless IoT device that is categorized as
"Raspberry Pi" clients. You see SSH traffic. You then check several more wireless IoT clients and see that they are sending SSH also.
You want an easy way to communicate the information that an IoT client has used SSH to Aruba ClearPass Policy Manager (CPPM).
What step should you take?
- A. On Central configure APs and gateways to use CPPM as the RADIUS accounting server.
- B. On CPPM create an Endpoint Context Server that points to the Central API.
- C. On Central set up CPPM as a Webhook application.
- D. On CPPM enable Device Insight integration.
Answer: B
Explanation:
Explanation
This is because an Endpoint Context Server (ECS) is a feature that allows ClearPass to receive contextual information from external sources, such as Aruba Central, and use it for policy enforcement and reporting. An ECS can be configured to point to the Aruba Central API and fetch data such as device type, category, OS, applications, traffic flows, etc.
An ECS can be used to communicate the information that an IoT client has used SSH to Aruba ClearPass Policy Manager (CPPM). The ECS can query the Aruba Central API and retrieve the network traffic flows of the wireless IoT devices that are categorized as "Raspberry Pi" clients. The ECS can then filter the traffic flows by the SSH protocol and send the relevant information to CPPM. CPPM can then use this information for policy decisions, such as allowing or denying SSH access, or triggering alerts or actions.
B: On CPPM enable Device Insight integration. This is not a valid step because Device Insight is a feature that allows ClearPass to discover, profile, and fingerprint devices on the network using deep packet inspection (DPI) and machine learning (ML). Device Insight does not communicate with Aruba Central or receive information from it. Moreover, Device Insight might not be able to detect SSH traffic on encrypted wireless IoT devices without decrypting it first.
C: On Central configure APs and gateways to use CPPM as the RADIUS accounting server. This is not a valid step because RADIUS accounting is a feature that allows network devices to send periodic updates about the status and activity of authenticated users or devices to a RADIUS server, such as CPPM. RADIUS accounting does not communicate with Aruba Central or receive information from it. Moreover, RADIUS accounting might not be able to capture SSH traffic on wireless IoT devices without inspecting it first.
D: On Central set up CPPM as a Webhook application. This is not a valid step because Webhook is a feature that allows Aruba Central to send notifications or events to external applications or services using HTTP requests. Webhook does not communicate with CPPM or send information to it. Moreover, Webhook might not be able to send SSH traffic information on wireless IoT devices without filtering it first.
NEW QUESTION # 18
A customer has an AOS 10 architecture, consisting of Aruba AP and AOS-CX switches, managed by Aruba Central. The customer wants to obtain information about the clients, such as their general category and OS.
What should you explain?
- A. The customer must deploy Aruba gateways in order to receive any client profiling information.
- B. The customer should set up a dedicated switch VSX group to sniff packets and direct them to Aruba Central.
- C. You will need to set up Aruba Central as a secondary IP helper for client VLANs, but this will not interfere with existing operations.
- D. Aruba Central will automatically derive this information using telemetry from the Aruba devices.
Answer: D
Explanation:
Explanation
Aruba Central can provide visibility and profiling of clients using the Client Insights feature, which is an AI-powered solution that uses native infrastructure telemetry to identify and classify clients based on their OS and general category. This feature does not require any additional hardware or software, such as gateways, IP helpers, or packet sniffers. It works by collecting and analyzing data from the Aruba APs and AOS-CX switches that are managed by Aruba Central. You can find more information about Client Insights in the Visibility and profiling solutions | HPE Aruba Networking page and the Clients Profile - Aruba page.
NEW QUESTION # 19
A company has an Aruba ClearPass server at 10.47.47.8, FQDN radius.acnsxtest.local. This exhibit shows ClearPass Policy Manager's (CPPM's) settings for an Aruba Mobility Controller (MC).
The MC is already configured with RADIUS authentication settings for CPPM, and RADIUS requests between the MC and CPPM are working. A network admin enters and commits this command to enable dynamic authorization on the MC:
aaa rfc-3576-server 10.47.47.8
But when CPPM sends CoA requests to the MC, they are not working. This exhibit shows the RFC 3576 server statistics on the MC:
How could you fix this issue?
- A. Make sure that CPPM is using an ArubaOS Wireless RADIUS CoA enforcement profile.
- B. Enable RadSec on the MCs' RFC 3676 server config.
- C. Configure the MC to obtain the time from a valid NTP server.
- D. Change the UDP port in the MCs' RFC 3576 server config to 3799.
Answer: D
Explanation:
Explanation
Dynamic authorization is a feature that allows CPPM to send change of authorization (CoA) or disconnect messages to the MC to modify or terminate a user session based on certain conditions or events 1. Dynamic authorization uses the RFC 3576 protocol, which is an extension of the RADIUS protocol 2.
To enable dynamic authorization on the MC, you need to configure the IP address and UDP port of the CPPM server as the RFC 3576 server on the MC 3. The default UDP port for RFC 3576 is 3799, but it can be changed on the CPPM server . The MC and CPPM must use the same UDP port for dynamic authorization to work properly 3.
In this scenario, the MC is configured with the IP address of the CPPM server (10.47.47.8) as the RFC 3576 server, but it is using the default UDP port of 3799. However, according to the exhibit, the CPPM server is using a different UDP port of 1700 for dynamic authorization . This mismatch causes the CoA requests from CPPM to fail on the MC, as shown by the statistics .
To fix this issue, you need to change the UDP port in the MCs' RFC 3576 server config to match the UDP port used by CPPM, which is 1700 in this case. Alternatively, you can change the UDP port in CPPM to match the default UDP port of 3799 on the MC. Either way, you need to ensure that both devices use the same UDP port for dynamic authorization 3 .
NEW QUESTION # 20
Refer to the scenario.
# Introduction to the customer
You are helping a company add Aruba ClearPass to their network, which uses Aruba network infrastructure devices.
The company currently has a Windows domain and Windows CA. The Window CA issues certificates to domain computers, domain users, and servers such as domain controllers. An example of a certificate issued by the Windows CA is shown here.
The company is in the process of adding Microsoft Endpoint Manager (Intune) to manage its mobile clients.
The customer is maintaining the on-prem AD for now and uses Azure AD Connect to sync with Azure AD.
# Requirements for issuing certificates to mobile clients
The company wants to use ClearPass Onboard to deploy certificates automatically to mobile clients enrolled in Intune. During this process, Onboard should communicate with Azure AD to validate the clients. High availability should also be provided for this scenario; in other words, clients should be able to get certificates from Subscriber 2 if Subscriber 1 is down.
The Intune admins intend to create certificate profiles that include a UPN SAN with the UPN of the user who enrolled the device.
# Requirements for authenticating clients
The customer requires all types of clients to connect and authenticate on the same corporate SSID.
The company wants CPPM to use these authentication methods:
* EAP-TLS to authenticate users on mobile clients registered in Intune
* TEAR, with EAP-TLS as the inner method to authenticate Windows domain computers and the users on them To succeed, EAP-TLS (standalone or as a TEAP method) clients must meet these requirements:
Their certificate is valid and is not revoked, as validated by OCSP
The client's username matches an account in AD
# Requirements for assigning clients to roles
After authentication, the customer wants the CPPM to assign clients to ClearPass roles based on the following rules:
* Clients with certificates issued by Onboard are assigned the "mobile-onboarded" role
* Clients that have passed TEAP Method 1 are assigned the "domain-computer" role Clients in the AD group "Medical" are assigned the "medical-staff" role Clients in the AD group "Reception" are assigned to the "reception-staff" role The customer requires CPPM to assign authenticated clients to AOS firewall roles as follows:
* Assign medical staff on mobile-onboarded clients to the "medical-mobile" firewall role
* Assign other mobile-onboarded clients to the "mobile-other" firewall role
* Assign medical staff on domain computers to the "medical-domain" firewall role
* All reception staff on domain computers to the "reception-domain" firewall role
* All domain computers with no valid user logged in to the "computer-only" firewall role
* Deny other clients access
# Other requirements
Communications between ClearPass servers and on-prem AD domain controllers must be encrypted.
# Network topology
For the network infrastructure, this customer has Aruba APs and Aruba gateways, which are managed by Central. APs use tunneled WLANs, which tunnel traffic to the gateway cluster. The customer also has AOS-CX switches that are not managed by Central at this point.
# ClearPass cluster IP addressing and hostnames
A customer's ClearPass cluster has these IP addresses:
* Publisher = 10.47.47.5
* Subscriber 1 = 10.47.47.6
* Subscriber 2 = 10.47.47.7
* Virtual IP with Subscriber 1 and Subscriber 2 = 10.47.47.8
The customer's DNS server has these entries
* cp.acnsxtest.com = 10.47.47.5
* cps1.acnsxtest.com = 10.47.47.6
* cps2.acnsxtest.com = 10.47.47.7
* radius.acnsxtest.com = 10.47.47.8
* onboard.acnsxtest.com = 10.47.47.8
The customer has now decided that it needs CPPM to assign certain mobile-onboarded devices to a
"nurse-call" AOS user role. These are mobile-onboarded devices that are communicating with IP address
10.1.18.12 using port 4343.
What are the prerequisites for fulfilling this requirement?
- A. Creating server-based role assignment rules on gateways that apply roles to clients based on traffic destinations
- B. Creating server-based role assignment rules on APs that apply roles to clients based on traffic destinations
- C. Creating a tag on Central to select the proper destination connection and integrating CPPM with Device Insight
- D. Setting up traffic classes and role mapping rules within Central's global settings
Answer: A
NEW QUESTION # 21
A customer's admins have added RF Protect licenses and enabled WIDS for a customer's AOS 8-based solution. The customer wants to use the built-in capabilities of APs without deploying dedicated air monitors (AMs). Admins tested rogue AP detection by connecting an unauthorized wireless AP to a switch. The rogue AP was not detected even after several hours.
What is one point about which you should ask?
- A. Whether the customer is using non-standard Wi-Fi channels in the deployment
- B. Whether admins enabled wireless containment
- C. Whether APs' switch ports support all the VLANs that are accessible at the edge
- D. Whether admins set at least one radio on each AP to air monitor mode
Answer: D
Explanation:
Explanation
RF Protect is a feature that enables wireless intrusion detection and prevention system (WIDS/WIPS) capabilities on AOS 8-based solutions. WIDS/WIPS allows detecting and mitigating rogue APs, unauthorized clients, and other wireless threats. RF Protect requires RF Protect licenses to be installed and WIDS to be enabled on the Mobility Master (MM).
To use the built-in capabilities of APs for WIDS/WIPS, without deploying dedicated air monitors (AMs), admins need to set at least one radio on each AP to air monitor mode. Air monitor mode allows the AP to scan the wireless spectrum and report any wireless activity or anomalies to the MM. Air monitor mode does not affect the other radio on the AP, which can still serve clients in access mode. By setting at least one radio on each AP to air monitor mode, admins can achieve full coverage and visibility of the wireless environment and detect rogue APs.
If admins do not set any radio on the APs to air monitor mode, the APs will not scan the wireless spectrum or report any wireless activity or anomalies to the MM. This means that the APs will not be able to detect rogue APs, even if they are connected to the same network. Therefore, admins should check whether they have set at least one radio on each AP to air monitor mode.
NEW QUESTION # 22
Refer to the scenario.
A customer has asked you to review their AOS-CX switches for potential vulnerabilities. The configuration for these switches is shown below:
What is one immediate remediation that you should recommend?
- A. Disabling Telnet
- B. Either disabling DHCPv4-snoopinq or leaving it enabled, but also enabling ARP inspection
- C. Setting the clock manually instead of using NTP
- D. Changing the switch's DNS server to the mgmt VRF
Answer: A
Explanation:
Explanation
According to the AOS-CX Switches Multiple Vulnerabilities1, one of the vulnerabilities (CVE-2021-41001) affects the Telnet service on AOS-CX switches. This vulnerability allows an unauthenticated remote attacker to cause a denial-of-service condition on the switch by sending specially crafted Telnet packets. The impact of this vulnerability is high, as it could result in a loss of management access and network disruption. Therefore, one immediate remediation that you should recommend is to disable Telnet on the switch. This way, the switch can prevent any malicious Telnet traffic from reaching it and avoid the exploitation of this vulnerability.
NEW QUESTION # 23
You want to use Device Insight tags as conditions within CPPM role mapping or enforcement policy rules.
What guidelines should you follow?
- A. Use the Endpoints Repository type for the rule conditions; Add Endpoints Repository as a secondary authentication source for services that use policies with these rules.
- B. Use the Application type for the rule conditions; no extra authorization source is required for services that use policies with these rules.
- C. Use the Endpoint type for the rule conditions; no extra authorization source is required for services that use policies with these rules.
- D. Create an HTTP authentication source to the Central API that queries for the tags. To use that source as the type for rule conditions, add it an authorization source for the service in question.
Answer: C
NEW QUESTION # 24
Refer to the scenario.
This customer is enforcing 802.1X on AOS-CX switches to Aruba ClearPass Policy Manager (CPPM). The customer wants switches to download role settings from CPPM. The "reception-domain" role must have these settings:
- Assigns clients to VLAN 14 on switch 1, VLAN 24 on switch 2, and so on.
- Filters client traffic as follows:
- Clients are permitted full access to 10.1.5.0/24 and the Internet
- Clients are denied access to 10.1.0.0/16
The switch topology is shown here:
How should you configure the VLAN setting for the reception role?
- A. Create a separate enforcement profile with a different VLAN ID for each switch. Add all profiles to the profile list in the appropriate enforcement policy rule.
- B. Assign a consistent name to VLAN 14, 24, or 34 on each access layer switch and reference that name in the enforcement profile VLAN settings.
- C. Assign a number-based ID to the access layer switches. Then use this variable in the enforcement profile VLAN settings: %(NAS-ID]4.
- D. Configure the enforcement profile as a downloadable role, but specify only the role name and leave the VLAN undefined. Then define a 'reception' role with the correct VLAN setting on each individual access layer switch.
Answer: B
NEW QUESTION # 25
Refer to the scenario.
A customer has an Aruba ClearPass cluster. The customer has AOS-CX switches that implement 802.1X authentication to ClearPass Policy Manager (CPPM).
Switches are using local port-access policies.
The customer wants to start tunneling wired clients that pass user authentication only to an Aruba gateway cluster. The gateway cluster should assign these clients to the "eth-internet" role. The gateway should also handle assigning clients to their VLAN, which is VLAN 20.
The plan for the enforcement policy and profiles is shown below:
The gateway cluster has two gateways with these IP addresses:
* Gateway 1
o VLAN 4085 (system IP) = 10.20.4.21
o VLAN 20 (users) = 10.20.20.1
o VLAN 4094 (WAN) = 198.51.100.14
* Gateway 2
o VLAN 4085 (system IP) = 10.20.4.22
o VLAN 20 (users) = 10.20.20.2
o VLAN 4094 (WAN) = 198.51.100.12
* VRRP on VLAN 20 = 10.20.20.254
The customer requires high availability for the tunnels between the switches and the gateway cluster. If one gateway falls, the other gateway should take over its tunnels. Also, the switch should be able to discover the gateway cluster regardless of whether one of the gateways is in the cluster.
What is one change that you should make to the solution?
- A. Configure edge ports in VLAN trunk mode.
- B. Configure the UBT solution to use VLAN extend mode.
- C. Remove VLAN assignments from role configurations on the gateways.
- D. Change the ubt-client-vlan to VLAN 13.
Answer: C
NEW QUESTION # 26
Refer to the scenario.
# Introduction to the customer
You are helping a company add Aruba ClearPass to their network, which uses Aruba network infrastructure devices.
The company currently has a Windows domain and Windows CA. The Window CA issues certificates to domain computers, domain users, and servers such as domain controllers. An example of a certificate issued by the Windows CA is shown here.
The company is in the process of adding Microsoft Endpoint Manager (Intune) to manage its mobile clients.
The customer is maintaining the on-prem AD for now and uses Azure AD Connect to sync with Azure AD.
# Requirements for issuing certificates to mobile clients
The company wants to use ClearPass Onboard to deploy certificates automatically to mobile clients enrolled in Intune. During this process, Onboard should communicate with Azure AD to validate the clients. High availability should also be provided for this scenario; in other words, clients should be able to get certificates from Subscriber 2 if Subscriber 1 is down.
The Intune admins intend to create certificate profiles that include a UPN SAN with the UPN of the user who enrolled the device.
# Requirements for authenticating clients
The customer requires all types of clients to connect and authenticate on the same corporate SSID.
The company wants CPPM to use these authentication methods:
EAP-TLS to authenticate users on mobile clients registered in Intune
TEAR, with EAP-TLS as the inner method to authenticate Windows domain computers and the users on them To succeed, EAP-TLS (standalone or as a TEAP method) clients must meet these requirements:
Their certificate is valid and is not revoked, as validated by OCSP
The client's username matches an account in AD
# Requirements for assigning clients to roles
After authentication, the customer wants the CPPM to assign clients to ClearPass roles based on the following rules:
Clients with certificates issued by Onboard are assigned the "mobile-onboarded" role Clients that have passed TEAP Method 1 are assigned the "domain-computer" role Clients in the AD group "Medical" are assigned the "medical-staff" role Clients in the AD group "Reception" are assigned to the "reception-staff" role The customer requires CPPM to assign authenticated clients to AOS firewall roles as follows:
Assign medical staff on mobile-onboarded clients to the "medical-mobile" firewall role Assign other mobile-onboarded clients to the "mobile-other" firewall role Assign medical staff on domain computers to the "medical-domain" firewall role All reception staff on domain computers to the "reception-domain" firewall role All domain computers with no valid user logged in to the "computer-only" firewall role Deny other clients access
# Other requirements
Communications between ClearPass servers and on-prem AD domain controllers must be encrypted.
# Network topology
For the network infrastructure, this customer has Aruba APs and Aruba gateways, which are managed by Central. APs use tunneled WLANs, which tunnel traffic to the gateway cluster. The customer also has AOS-CX switches that are not managed by Central at this point.
# ClearPass cluster IP addressing and hostnames
A customer's ClearPass cluster has these IP addresses:
Publisher = 10.47.47.5
Subscriber 1 = 10.47.47.6
Subscriber 2 = 10.47.47.7
Virtual IP with Subscriber 1 and Subscriber 2 = 10.47.47.8
The customer's DNS server has these entries
cp.acnsxtest.com = 10.47.47.5
cps1.acnsxtest.com = 10.47.47.6
cps2.acnsxtest.com = 10.47.47.7
radius.acnsxtest.com = 10.47.47.8
onboard.acnsxtest.com = 10.47.47.8
On CPPM, you are creating the authentication method shown in the exhibit below:
You will use the method for standalone EAP-TLS and for inner methods in TEAP.
What should you do?
- A. Configure OCSP override and leave the OCSP URL blank.
- B. Enable authorization.
- C. Enable certificate comparison.
- D. Configure OCSP override and set the OCSP URL to localhost/onboard/mdps ocspphp/2
Answer: D
NEW QUESTION # 27
Refer to the scenario.
# Introduction to the customer
You are helping a company add Aruba ClearPass to their network, which uses Aruba network infrastructure devices.
The company currently has a Windows domain and Windows CA. The Window CA issues certificates to domain computers, domain users, and servers such as domain controllers. An example of a certificate issued by the Windows CA is shown here.
The company is in the process of adding Microsoft Endpoint Manager (Intune) to manage its mobile clients.
The customer is maintaining the on-prem AD for now and uses Azure AD Connect to sync with Azure AD.
# Requirements for issuing certificates to mobile clients
The company wants to use ClearPass Onboard to deploy certificates automatically to mobile clients enrolled in Intune. During this process, Onboard should communicate with Azure AD to validate the clients. High availability should also be provided for this scenario; in other words, clients should be able to get certificates from Subscriber 2 if Subscriber 1 is down.
The Intune admins intend to create certificate profiles that include a UPN SAN with the UPN of the user who enrolled the device.
# Requirements for authenticating clients
The customer requires all types of clients to connect and authenticate on the same corporate SSID.
The company wants CPPM to use these authentication methods:
EAP-TLS to authenticate users on mobile clients registered in Intune
TEAR, with EAP-TLS as the inner method to authenticate Windows domain computers and the users on them To succeed, EAP-TLS (standalone or as a TEAP method) clients must meet these requirements:
Their certificate is valid and is not revoked, as validated by OCSP
The client's username matches an account in AD
# Requirements for assigning clients to roles
After authentication, the customer wants the CPPM to assign clients to ClearPass roles based on the following rules:
Clients with certificates issued by Onboard are assigned the "mobile-onboarded" role Clients that have passed TEAP Method 1 are assigned the "domain-computer" role Clients in the AD group "Medical" are assigned the "medical-staff" role Clients in the AD group "Reception" are assigned to the "reception-staff" role The customer requires CPPM to assign authenticated clients to AOS firewall roles as follows:
Assign medical staff on mobile-onboarded clients to the "medical-mobile" firewall role Assign other mobile-onboarded clients to the "mobile-other" firewall role Assign medical staff on domain computers to the "medical-domain" firewall role All reception staff on domain computers to the "reception-domain" firewall role All domain computers with no valid user logged in to the "computer-only" firewall role Deny other clients access
# Other requirements
Communications between ClearPass servers and on-prem AD domain controllers must be encrypted.
# Network topology
For the network infrastructure, this customer has Aruba APs and Aruba gateways, which are managed by Central. APs use tunneled WLANs, which tunnel traffic to the gateway cluster. The customer also has AOS-CX switches that are not managed by Central at this point.
# ClearPass cluster IP addressing and hostnames
A customer's ClearPass cluster has these IP addresses:
Publisher = 10.47.47.5
Subscriber 1 = 10.47.47.6
Subscriber 2 = 10.47.47.7
Virtual IP with Subscriber 1 and Subscriber 2 = 10.47.47.8
The customer's DNS server has these entries
cp.acnsxtest.com = 10.47.47.5
cps1.acnsxtest.com = 10.47.47.6
cps2.acnsxtest.com = 10.47.47.7
radius.acnsxtest.com = 10.47.47.8
onboard.acnsxtest.com = 10.47.47.8
You cannot see flow attributes for wireless clients.
What should you check?
- A. Firewall application visibility is enabled on the Aruba gateways, and the gateways have been rebooted.
- B. Deep packet inspection is enabled on the Aruba Aps, and the APs have been rebooted.
- C. Gateway IDS/IPS is enabled on the Aruba gateways, and the gateways have been rebooted.
- D. Deep packet inspection is enabled on the role to which the Aruba APs assign the wireless clients.
Answer: D
NEW QUESTION # 28
Refer to the scenario.
A customer has an Aruba ClearPass cluster. The customer has AOS-CX switches that implement 802.1X authentication to ClearPass Policy Manager (CPPM).
Switches are using local port-access policies.
The customer wants to start tunneling wired clients that pass user authentication only to an Aruba gateway cluster. The gateway cluster should assign these clients to the "eth-internet" role. The gateway should also handle assigning clients to their VLAN, which is VLAN 20.
The plan for the enforcement policy and profiles is shown below:
The gateway cluster has two gateways with these IP addresses:
* Gateway 1
o VLAN 4085 (system IP) = 10.20.4.21
o VLAN 20 (users) = 10.20.20.1
o VLAN 4094 (WAN) = 198.51.100.14
* Gateway 2
o VLAN 4085 (system IP) = 10.20.4.22
o VLAN 20 (users) = 10.20.20.2
o VLAN 4094 (WAN) = 198.51.100.12
* VRRP on VLAN 20 = 10.20.20.254
The customer requires high availability for the tunnels between the switches and the gateway cluster. If one gateway falls, the other gateway should take over its tunnels. Also, the switch should be able to discover the gateway cluster regardless of whether one of the gateways is in the cluster.
You are setting up the UBT zone on an AOS-CX switch.
Which IP addresses should you define in the zone?
- A. [Primary controller = 198.51.100.14; backup controller = 10.20.4.21
- B. Primary controller = 10 20 4 21:backup controller not defined
- C. Primary controller = 10.20.20.254; backup controller, not defined
- D. Primary controller = 10.20.4.21; backup controller = 10.20.4.22
Answer: D
NEW QUESTION # 29
Refer to the scenario.
A customer has an Aruba ClearPass cluster. The customer has AOS-CX switches that implement 802.1X authentication to ClearPass Policy Manager (CPPM).
Switches are using local port-access policies.
The customer wants to start tunneling wired clients that pass user authentication only to an Aruba gateway cluster. The gateway cluster should assign these clients to the "eth-internet" role. The gateway should also handle assigning clients to their VLAN, which is VLAN 20.
The plan for the enforcement policy and profiles is shown below:
The gateway cluster has two gateways with these IP addresses:
* Gateway 1
o VLAN 4085 (system IP) = 10.20.4.21
o VLAN 20 (users) = 10.20.20.1
o VLAN 4094 (WAN) = 198.51.100.14
* Gateway 2
o VLAN 4085 (system IP) = 10.20.4.22
o VLAN 20 (users) = 10.20.20.2
o VLAN 4094 (WAN) = 198.51.100.12
* VRRP on VLAN 20 = 10.20.20.254
The customer requires high availability for the tunnels between the switches and the gateway cluster. If one gateway falls, the other gateway should take over its tunnels. Also, the switch should be able to discover the gateway cluster regardless of whether one of the gateways is in the cluster.
What is one change that you should make to the solution?
- A. Configure edge ports in VLAN trunk mode.
- B. Configure the UBT solution to use VLAN extend mode.
- C. Remove VLAN assignments from role configurations on the gateways.
- D. Change the ubt-client-vlan to VLAN 13.
Answer: C
Explanation:
Explanation
The UBT solution requires that the VLAN assignments for the wired clients are done by the gateway, not by the switch. Therefore, the role configurations on the gateways should not have any VLAN assignments, as they would override the VLAN 20 that is specified in the enforcement profile. Instead, the role configurations should only have policies that define the access rights for the clients in the "eth-internet" role. This way, the gateway can assign the clients to VLAN 20 and apply the appropriate policies based on their role1
NEW QUESTION # 30
Refer to the scenario.
# Introduction to the customer
You are helping a company add Aruba ClearPass to their network, which uses Aruba network infrastructure devices.
The company currently has a Windows domain and Windows CA. The Window CA issues certificates to domain computers, domain users, and servers such as domain controllers. An example of a certificate issued by the Windows CA is shown here.
The company is in the process of adding Microsoft Endpoint Manager (Intune) to manage its mobile clients.
The customer is maintaining the on-prem AD for now and uses Azure AD Connect to sync with Azure AD.
# Requirements for issuing certificates to mobile clients
The company wants to use ClearPass Onboard to deploy certificates automatically to mobile clients enrolled in Intune. During this process, Onboard should communicate with Azure AD to validate the clients. High availability should also be provided for this scenario; in other words, clients should be able to get certificates from Subscriber 2 if Subscriber 1 is down.
The Intune admins intend to create certificate profiles that include a UPN SAN with the UPN of the user who enrolled the device.
# Requirements for authenticating clients
The customer requires all types of clients to connect and authenticate on the same corporate SSID.
The company wants CPPM to use these authentication methods:
* EAP-TLS to authenticate users on mobile clients registered in Intune
* TEAR, with EAP-TLS as the inner method to authenticate Windows domain computers and the users on them To succeed, EAP-TLS (standalone or as a TEAP method) clients must meet these requirements:
Their certificate is valid and is not revoked, as validated by OCSP
The client's username matches an account in AD
# Requirements for assigning clients to roles
After authentication, the customer wants the CPPM to assign clients to ClearPass roles based on the following rules:
* Clients with certificates issued by Onboard are assigned the "mobile-onboarded" role
* Clients that have passed TEAP Method 1 are assigned the "domain-computer" role Clients in the AD group "Medical" are assigned the "medical-staff" role Clients in the AD group "Reception" are assigned to the "reception-staff" role The customer requires CPPM to assign authenticated clients to AOS firewall roles as follows:
* Assign medical staff on mobile-onboarded clients to the "medical-mobile" firewall role
* Assign other mobile-onboarded clients to the "mobile-other" firewall role
* Assign medical staff on domain computers to the "medical-domain" firewall role
* All reception staff on domain computers to the "reception-domain" firewall role
* All domain computers with no valid user logged in to the "computer-only" firewall role
* Deny other clients access
# Other requirements
Communications between ClearPass servers and on-prem AD domain controllers must be encrypted.
# Network topology
For the network infrastructure, this customer has Aruba APs and Aruba gateways, which are managed by Central. APs use tunneled WLANs, which tunnel traffic to the gateway cluster. The customer also has AOS-CX switches that are not managed by Central at this point.
# ClearPass cluster IP addressing and hostnames
A customer's ClearPass cluster has these IP addresses:
* Publisher = 10.47.47.5
* Subscriber 1 = 10.47.47.6
* Subscriber 2 = 10.47.47.7
* Virtual IP with Subscriber 1 and Subscriber 2 = 10.47.47.8
The customer's DNS server has these entries
* cp.acnsxtest.com = 10.47.47.5
* cps1.acnsxtest.com = 10.47.47.6
* cps2.acnsxtest.com = 10.47.47.7
* radius.acnsxtest.com = 10.47.47.8
* onboard.acnsxtest.com = 10.47.47.8
On CPPM, you are creating the authentication method shown in the exhibit below:
You will use the method for standalone EAP-TLS and for inner methods in TEAP.
What should you do?
- A. Configure OCSP override and leave the OCSP URL blank.
- B. Enable authorization.
- C. Enable certificate comparison.
- D. Configure OCSP override and set the OCSP URL to localhost/onboard/mdps ocspphp/2
Answer: D
NEW QUESTION # 31
Refer to the scenario.
A customer is migrating from on-prem AD to Azure AD as its sole domain solution. The customer also manages both wired and wireless devices with Microsoft Endpoint Manager (Intune).
The customer wants to improve security for the network edge. You are helping the customer design a ClearPass deployment for this purpose. Aruba network devices will authenticate wireless and wired clients to an Aruba ClearPass Policy Manager (CPPM) cluster (which uses version 6.10).
The customer has several requirements for authentication. The clients should only pass EAP-TLS authentication if a query to Azure AD shows that they have accounts in Azure AD. To further refine the clients' privileges, ClearPass also should use information collected by Intune to make access control decisions.
Assume that the Azure AD deployment has the proper prerequisites established.
You are planning the CPPM authentication source that you will reference as the authentication source in
802.1X services.
How should you set up this authentication source?
- A. As Kerberos type
- B. As Active Directory type
- C. As HTTP type, referencing the Intune extension
- D. AS HTTP type, referencing Azure AD's FODN
Answer: D
Explanation:
Explanation
An authentication source is a configuration element in CPPM that defines how to connect to an external identity provider and retrieve user or device information . CPPM supports various types of authentication sources, such as Active Directory, LDAP, SQL, Kerberos, and HTTP .
To authenticate wireless and wired clients to Azure AD, you need to set up an authentication source as HTTP type, referencing Azure AD's FQDN . This type of authentication source allows CPPM to use REST API calls to communicate with Azure AD and validate the user or device credentials . You also need to configure the OAuth 2.0 settings for the authentication source, such as the client ID, client secret, token URL, and resource URL .
To use information collected by Intune to make access control decisions, you need to set up another authentication source as HTTP type, referencing the Intune extension . This type of authentication source allows CPPM to use REST API calls to communicate with Intune and retrieve the device compliance status .
You also need to configure the OAuth 2.0 settings for the authentication source, such as the client ID, client secret, token URL, and resource URL .
NEW QUESTION # 32
......
HP HPE6-A84 Exam Practice Test Questions: https://certificationsdesk.examslabs.com/HP/HP-ACA-Network-Security/best-HPE6-A84-exam-dumps.html